GoVertical
New member
Vertically stacked stators and rotors PMA.
Greetings, I have been working on a vertically stacked stators and rotors permanent magnet alternator. The stators are wired in series with 8 coils per stators. I used 22 gauge wire, 2 in hand with 100 turns, but any size wire can be used. Each stator is offset the with of the coil leg to create a 3 phase configuration.
There are four rotors. The inner two rotors are metal free and the outer rotors are metal backed. This configuration allows for ½ the magnets to be used and still forms the magnetic circuit of a traditional axial flux design.
The case is a 6 inch PVC coupler and the stator spacer are pieces of 6 inch PVC tubing. Using off the shelve parts a 8 inch version with more coils and magnets could easily be configured. Hubs are used to attach the rotors to the central spinning axis.
I have found this configuration easy to fabricate, it allows for a increase in coil count while using less magnets then traditional fabrication techniques. The stators can be easily wired in a Star or Delta configuration. I am currently waiting for warmer weather to complete testing. From the limited test data that I was able to complete has shown that the increase coil count has created a higher voltage output at a lower RPM. Comments welcome.
Pystysuoraan päällekkäin staattorit ja roottorit PMA.
Tervehdys, olen työskennellyt vertikaalisesti pinota staattorit ja roottorit kestomagneetti laturi. Staattorit on kytketty sarjaan 8 kelat kohti staattoreita. Käytin 22 paksuinen johto, 2 kädessä 100 kierrosta, mutta minkä kokoista johto voidaan käyttää. Jokainen staattori on offset kanssa sekä kelan jalka luoda 3 vaihe kokoonpano.
On neljä roottorit. Sisempi kaksi roottorit ovat metallia ilmaiseksi ja ulompi roottorit ovat metallia tukena. Tämä kokoonpano mahdollistaa ½ magneetteja voidaan käyttää ja muodostaa yhä loistevalojen perinteisen aksiaalivuokone design.
Jos on 6 tuuman PVC liitin ja staattorin Vanha ovat kpl 6 tuuman PVC-putkilla. Käyttämällä pois hyllyttämistä osat 8 tuuman versio lisää keloja ja magneetit voivat helposti konfiguroida. Hubit käytetään liittämään roottorit Keski pyörivät akselin ympäri.
Olen huomannut tämän kokoonpanon helppo valmistaa, se mahdollistaa kasvun kela laskea käyttämällä vähemmän magneetteja sitten perinteinen valmistustekniikalla. Staattorit helposti kytketty tähti tai kolmio kokoonpano. Olen tällä hetkellä odottaa lämpimämmän ja täydellinen testaus. Rajoitetusta testitulokset että pystyin loppuun on osoittanut, että kasvu kela määrä on luotu suurempi lähtöjännite on pienempi RPM. Kommentit tervetulleita.
Greetings, I have been working on a vertically stacked stators and rotors permanent magnet alternator. The stators are wired in series with 8 coils per stators. I used 22 gauge wire, 2 in hand with 100 turns, but any size wire can be used. Each stator is offset the with of the coil leg to create a 3 phase configuration.
There are four rotors. The inner two rotors are metal free and the outer rotors are metal backed. This configuration allows for ½ the magnets to be used and still forms the magnetic circuit of a traditional axial flux design.
The case is a 6 inch PVC coupler and the stator spacer are pieces of 6 inch PVC tubing. Using off the shelve parts a 8 inch version with more coils and magnets could easily be configured. Hubs are used to attach the rotors to the central spinning axis.
I have found this configuration easy to fabricate, it allows for a increase in coil count while using less magnets then traditional fabrication techniques. The stators can be easily wired in a Star or Delta configuration. I am currently waiting for warmer weather to complete testing. From the limited test data that I was able to complete has shown that the increase coil count has created a higher voltage output at a lower RPM. Comments welcome.
Pystysuoraan päällekkäin staattorit ja roottorit PMA.
Tervehdys, olen työskennellyt vertikaalisesti pinota staattorit ja roottorit kestomagneetti laturi. Staattorit on kytketty sarjaan 8 kelat kohti staattoreita. Käytin 22 paksuinen johto, 2 kädessä 100 kierrosta, mutta minkä kokoista johto voidaan käyttää. Jokainen staattori on offset kanssa sekä kelan jalka luoda 3 vaihe kokoonpano.
On neljä roottorit. Sisempi kaksi roottorit ovat metallia ilmaiseksi ja ulompi roottorit ovat metallia tukena. Tämä kokoonpano mahdollistaa ½ magneetteja voidaan käyttää ja muodostaa yhä loistevalojen perinteisen aksiaalivuokone design.
Jos on 6 tuuman PVC liitin ja staattorin Vanha ovat kpl 6 tuuman PVC-putkilla. Käyttämällä pois hyllyttämistä osat 8 tuuman versio lisää keloja ja magneetit voivat helposti konfiguroida. Hubit käytetään liittämään roottorit Keski pyörivät akselin ympäri.
Olen huomannut tämän kokoonpanon helppo valmistaa, se mahdollistaa kasvun kela laskea käyttämällä vähemmän magneetteja sitten perinteinen valmistustekniikalla. Staattorit helposti kytketty tähti tai kolmio kokoonpano. Olen tällä hetkellä odottaa lämpimämmän ja täydellinen testaus. Rajoitetusta testitulokset että pystyin loppuun on osoittanut, että kasvu kela määrä on luotu suurempi lähtöjännite on pienempi RPM. Kommentit tervetulleita.